Waterjet Cutting Copper & Brass: Zero Laser Back-Reflection, High Thermal Dissipation & Clean Edges
Category:News Center
Author: Wonlean Waterjet
Source: Wonlean Waterjet
Add time:2026-10-21 10:02
Pure copper (C11000 ETP, C10100 OFHC) and copper alloys like brass (C26000, C36000) and bronze are critical for EV battery busbars, switchgear distribution panels, electrical transformers, and decorative architectural metalwork. However, copper and brass present two notorious engineering roadblocks for thermal cutting equipment:
First, pure copper reflects over 95% of standard 1,064 nm fiber laser beams, creating severe back-reflection that can destroy laser cutting heads and fiber feed cables. Second, copper's immense thermal conductivity ($401\,\text{W/m}\cdot\text{K}$) rapidly dissipates heat away from a thermal cutting zone, requiring massive heat inputs that scorch adjacent areas and cause severe copper oxide discoloration.
Abrasive waterjet cutting is completely immune to optical reflectivity and thermal conductivity, making it the safest, most precise method for profiling copper and brass plate up to 100 mm thick.
⚡ Copper Fabrication: Waterjet vs. Laser Cutting
• Zero Back-Reflection Hazard: Waterjet uses water and garnet abrasive. Reflective optical feedback does not exist — zero risk of equipment damage.
• Maintains 100% IACS Electrical Conductivity: Thermal cutting anneals copper and oxidizes surface layers, degrading contact resistance. Waterjet cuts at room temperature with zero conductivity degradation.
• Clean Burr-Free Busbar Bolt Holes: Cuts precision oval slots and mounting holes in 15 mm copper busbars ready for silver/tin plating without deburring.
Wonlean Cutting Speeds for C110 Copper and C360 Brass
Copper is relatively ductile, while brass is slightly harder and cuts crisply. Benchmark cutting speeds on Wonlean 420 MPa systems with 80-mesh garnet:
| Thickness (mm) | C110 Pure Copper (Q3 Speed) | C360 Free-Cutting Brass (Q3 Speed) | Edge Finish ($Ra$) |
|---|---|---|---|
| 3 mm (1/8 in) | 2,200 mm/min | 2,600 mm/min | $Ra$ 2.8 – 3.5 µm |
| 10 mm (3/8 in) | 580 mm/min | 690 mm/min | $Ra$ 3.2 – 4.2 µm |
| 25 mm (1 in) | 200 mm/min | 240 mm/min | $Ra$ 3.8 – 4.8 µm |
| 50 mm (2 in) | 75 mm/min | 92 mm/min | $Ra$ 4.5 – 5.5 µm |
| 75 mm (3 in) | 35 mm/min | 42 mm/min | $Ra$ 5.2 – 6.0 µm |
Target Applications: EV Power Distribution & Luxury Architecture
⚡ EV Battery Module & Inverter Busbars:
Heavy copper busbars require tight contact tolerances and burr-free surfaces. Burrs can puncture insulation barriers in high-voltage 800V EV architectures. Wonlean waterjets slice complex bent busbar blanks with zero edge burr.
🏛️ Luxury Architectural Brass Screens & Inlays:
Decorative architectural facades, brass elevator grilles, and floor inlay strips cut cleanly without heat discoloration, preserving mirror and satin brass finishes without tedious hand polishing.
Frequently Asked Questions
Safely Cut Reflective Copper & Brass with Wonlean
Eliminate laser back-reflection and achieve 100% electrical conductivity preservation. Contact our technical team today.
📧 wonlean@wonlinwaterjet.com | 📞 +86 135 9192 8579 | 🌐 www.wonlean.cn
waterjet cutting copper,cutting brass with waterjet,waterjet vs laser copper cutting,copper busbar waterjet cutting,high conductivity copper waterjet machine,waterjet copper cutting machine
Related News